Polypropylene PP glass fiber composite materials Polypropylene homopolymer long glass fiber is polymerized from a single propylene monomer, with high crystallinity, good mechanical strength and heat resistance.

PP glass fiber composite materials Polypropylene Polypropylene homopolymer long glass fiber is polymerized from a single propylene monomer, with high crystallinity, good mechanical strength and heat resistance.

HPP is Homopolymer polypropylene

What is long glass fiber? Long glass fiber reinforced plastic is on the basis of the original pure plastic, adding long glass fiber and other additives, so as to improve the scope of use of materials. Why filling Long Glass Fiber? 1. After long glass fiber reinforcement, long glass fiber is a high temperature resistant material, therefore, the heat resistance temperature of reinforced plastics is much higher than before without long glass fiber, especially nylon plastics; 2. After long glass fiber reinforcement, due to the addition of long glass fiber, limited the mutual movement between polymer chains of plastics, therefore, the shrinkage rate of reinforced plastics decreases a lot, rigidity is greatly improved; 3. After long glass fiber reinforcement, the reinforced plastic will not stress crack, at the same time, the anti-impact performance of plastic is improved a lot; 4. After long glass fiber reinforcement, long glass fiber is a high strength material, which also greatly improves the strength of plastic, such as: tensile strength, compression strength, bending strength, improve a lot; 5. Long glass fiber reinforced after, due to the addition of long glass fiber and other additives, the combustion performance of reinforced plastics decreased a lot, most of the material can not ignite, is a kind of flame retardant material. Why choose Long Glass Fiber instead of Short Glass Fiber? Compared with short fiber reinforced thermoplastic composites, LFT has the following advantages: • Long fiber length, significantly improve the mechanical properties of products. • High specific stiffness and strength, good impact resistance, especially suitable for automotive applications. • Improved creep resistance, good dimensional stability, high parts forming accuracy. • Excellent fatigue resistance. • Better stability in hot and humid environments. • The fiber can move relatively in the molding mold during the molding process, and the fiber damage is small. Appearance of PP-LGF      Application of PP-LGF Automotive parts Front end module, door module, shift mechanism, electronic accelerator pedal, dashboard skeleton, cooling fan and frame, battery carrier, bumper bracket, underbody protection plate, sunroof frame, etc., used to replace reinforced PA or metal materials. Household appliance Washing machine drum, washing machine triangle bracket, one brush machine drum, air conditioning fan, etc., used to replace short glass fiber reinforced PA, APS metal materials. Communications, electronics, electrical appliances High-precision connectors, igniter components, coil shaft, relay base, microwave oven transformer coil frame/frame, electrical connector, solenoid valve package, scanner components, etc. Others Power tool housing, water pump or water meter housing, impeller, bicycle skeleton, skis, ground locomotive pedals, military/civil safety helmets, safety shoes, etc. are used to replace short glass fiber reinforced PA, PPO, etc. TDS for reference About us Xiamen LFT composite plastic Co., Ltd. is a brand-name company that focuses on LFT&LFRT. Long Glass Fiber Series (LGF) & Long Carbon Fiber Series (LCF). The company's thermoplastic LFT can be used for LFT-G injection molding and extrusion, and can also be used for LFT-D molding. It can be produced according to customer requirements: 5~25mm length. The company's long-fiber continuous infiltration reinforced thermoplastics have passed ISO9001 &16949 system certification, and the products have obtained lots of national trademarks and patents. We will offer you: 1. LFT&LFRT material technical parameters and leading edge design; 2. Mold front design and recommendations; 3. Provide technical support such as injection molding and extrusion molding.

PP-LGF Among many composite materials, long glass reinforced polypropylene material (PP-LGF) has gained more popularity for its low price, excellent mechanical properties and environmental friendliness.Compared with short glass fiber reinforced polypropylene material (PP-SGF), PP-LGF has more advantages in strength, stiffness, warpage, fatigue resistance, notch impact strength and dimensional stability, so products produced with PP-LGF can further achieve weight and cost reduction. The length of PP-LGF particles produced by our company is generally 8mm~15mm, in which the content of glass fiber can reach 20%~60%, and the retained length of glass fiber in the particles can reach 1mm~3mm, compared with PP-SGF materials whose retained length of glass fiber is only 0.2mm~0.4mm, PP-LGF can guarantee the following characteristics due to the three-dimensional network structure of its internal fiber.  1. Low density: The use of long glass fiber reinforced composite material instead of steel is an effective way to reduce the weight of the product.  2. High strength: The composite material with modified resin and different length of fiber has high mechanical strength, good rigidity and impact performance, which can replace steel plate to make coverings or structural parts. 3. Low cost: The use of long glass fiber reinforced composite materials instead of metal materials can simplify the design of complex metal parts and achieve the purpose of forming complex parts at one time. 4. Impact resistance: The elastic deformation property of resin makes long glass fiber reinforced composite materials have certain function of absorbing collision energy, and have a large buffering effect on the impact of certain speed. 5. Corrosion resistance: The composite material has strong corrosion resistance, and its corrosion resistance to acid, alkali and salt is better than that of metal. 6. Beauty: most resins have good colorability, and can be made into various colors by adding masterbatch or spraying paint on the surface; through injection and molding, various irregular curvature shapes can be realized. Datasheet for reference Tests Application As the hottest material, our customers have applied the PP-LGF in many fields, like car parts, washing machine parts, etc. Just contact us, and we will provide technical support. About company Xiamen LFT composite plastic Co., Ltd. is a brand-name company that focuses on LFT&LFRT. Long Glass Fiber Series (LGF) & Long Carbon Fiber Series (LCF). The company's thermoplastic LFT can be used for LFT-G injection molding and extrusion, and can also be used for LFT-D molding. It can be produced according to customer requirements: 5~25mm length. The company's long-fiber continuous infiltration reinforced thermoplastics have passed ISO9001&16949 system certification, and the products have obtained lots of national trademarks and patents.

PP-LCF composites Polypropylene is a low-cost, excellent performance, widely used polymer materials, through the carbon fiber reinforced, can improve the strength, heat distortion temperature and dimensional stability of polypropylene materials, expanding the application of polypropylene materials, widely used in electronic and electrical appliances, automotive, construction and other fields. Especially in the automotive field, with the development of new energy vehicles and in the trend of automotive lightweight, carbon fiber reinforced materials in the automotive field is more and more widely used. Characteristics of long carbon fiber reinforced polypropylene materials Higher mechanical properties Simple production, easy molding, low warpage Lower density, lightweight, can replace steel with plastic Application The modified polypropylene material reinforced by carbon fiber has a series of advantages such as light weight, high modulus, high specific strength, low coefficient of thermal expansion, high temperature resistance, thermal shock resistance, corrosion resistance, good vibration absorption and so on, and it can be applied to automobile sub-instrument assembly and other automobile parts. Car Tool Kit Automotive front-end components More application fields, please contact us for more technical advice. Frequently asked questions 1. What are the types of thermoplastic carbon fiber composites? Carbon fiber thermoplastic composites are composites with carbon fiber as reinforcing material and thermoplastic resin as matrix. From the reinforcement of carbon fiber, it can be divided into long-cut carbon fiber (LCF)-reinforced thermoplastic composites, short-cut carbon fiber (SCF)-reinforced thermoplastic composites and continuous carbon fiber (CCF)-reinforced thermoplastic composites. Long-cut carbon fiber and short-cut carbon fiber mainly refers to the application length of carbon fiber materials, there is no strict fixed distinction between the two, generally between a few millimeters to a few centimeters, the more common specifications are 6mm, 12mm, 20mm, 30mm, 50mm. Carbon fiber thermoplastic composites can also be classified according to the thermoplastic resin, there are many common thermoplastic resins, such as PE, PP, PVC, etc., but the thermoplastic resin composites reinforced with carbon fibers are mostly used in aerospace, precision equipment, and other demanding working environments, so the carbon fiber thermoplastic composites are more commonly used in the form of polyetheretherketone (PEEK), PPS, polyimide ( Therefore, carbon fiber thermoplastic composites more often use polyether ether ketone (PEEK), PPS, polyimide (PI), polyetherimide (PAI) and other high-end thermoplastic resins as the matrix, to achieve the optimization of the material performance through the way of "strong alliance". 2. How do thermoplastic carbon fiber composites achieve low cost and environmental protection? Thermoplastic carbon fiber composites are used to make parts for high-end machinery, and they have excellent machinability, vacuum forming, stamping mold plasticity and bending processability, etc. Moreover, as long as the material reaches a certain temperature again, it can be remolded, which is recyclable and environmentally friendly in terms of the characteristics of the material itself. For example, Teijin Japan has been able to design a recycling process in the process according to the special needs, and the punched thermoplastic carbon fiber composite material trimmings are shredded, injection molded, and made into recycled materials, which can be used to make small products or injection molded nuts and studs on the carbon fiber prototype parts. This method can reduce the loss of raw materials to a greater extent, improve the use of thermoplastic carbon fiber composite materials, reduce the overall cost, so as to achieve the purpose of environmental protection. Production process of thermoplastic carbon fiber products In addition, thermoplastic carbon fiber composites, compared with thermoset carbon fiber composites, can shorten the molding cycle time due to its special process characteristics, which can further cut down the production cost in terms of production efficiency. 3. Are thermoplastic carbon fiber composites only suitable for injection molding? From the process point of view, injection molding and compression molding compared to a higher degree of automation, the raw material does not contact with the outside world, so the product appearance quality is guaranteed, there will be no black spots, impurities, uneven color and other issues, the mechanical properties of the product, dimensional stability and precision is relatively higher. At present, Toray, Japan, these carbon fiber giants in the application of carbon fiber reinforced thermoplastic composite materials, the main use of injection molding method, and this method is suitable for the production of complex shaped parts and mass production. Com...

PP-LGF Among many composite materials, long glass reinforced polypropylene material (PP-LGF) has gained more popularity for its low price, excellent mechanical properties and environmental friendliness.Compared with short glass fiber reinforced polypropylene material (PP-SGF), PP-LGF has more advantages in strength, stiffness, warpage, fatigue resistance, notch impact strength and dimensional stability, so products produced with PP-LGF can further achieve weight and cost reduction. The length of PP-LGF particles produced by our company is generally 8mm~15mm, in which the content of glass fiber can reach 20%~60%, and the retained length of glass fiber in the particles can reach 1mm~3mm, compared with PP-SGF materials whose retained length of glass fiber is only 0.2mm~0.4mm, PP-LGF can guarantee the following characteristics due to the three-dimensional network structure of its internal fiber.  1. Low density: The use of long glass fiber reinforced composite material instead of steel is an effective way to reduce the weight of the product.  2. High strength: The composite material with modified resin and different length of fiber has high mechanical strength, good rigidity and impact performance, which can replace steel plate to make coverings or structural parts. 3. Low cost: The use of long glass fiber reinforced composite materials instead of metal materials can simplify the design of complex metal parts and achieve the purpose of forming complex parts at one time. 4. Impact resistance: The elastic deformation property of resin makes long glass fiber reinforced composite materials have certain function of absorbing collision energy, and have a large buffering effect on the impact of certain speed. 5. Corrosion resistance: The composite material has strong corrosion resistance, and its corrosion resistance to acid, alkali and salt is better than that of metal. 6. Beauty: most resins have good colorability, and can be made into various colors by adding masterbatch or spraying paint on the surface; through injection and molding, various irregular curvature shapes can be realized. Datasheet for reference Tests Application As the hottest material, our customers have applied the PP-LGF in many fields, like car parts, washing machine parts, etc. Just contact us, and we will provide technical support. About company Xiamen LFT composite plastic Co., Ltd. is a brand-name company that focuses on LFT&LFRT. Long Glass Fiber Series (LGF) & Long Carbon Fiber Series (LCF). The company's thermoplastic LFT can be used for LFT-G injection molding and extrusion, and can also be used for LFT-D molding. It can be produced according to customer requirements: 5~25mm length. The company's long-fiber continuous infiltration reinforced thermoplastics have passed ISO9001&16949 system certification, and the products have obtained lots of national trademarks and patents.

HPP is Homopolymer polypropylene

HPP is Homopolymer polypropylene

HPP is Homopolymer polypropylene

PP-LGF Among many composite materials, long glass reinforced polypropylene material (PP-LGF) has gained more popularity for its low price, excellent mechanical properties and environmental friendliness.Compared with short glass fiber reinforced polypropylene material (PP-SGF), PP-LGF has more advantages in strength, stiffness, warpage, fatigue resistance, notch impact strength and dimensional stability, so products produced with PP-LGF can further achieve weight and cost reduction. The length of PP-LGF particles produced by our company is generally 8mm~15mm, in which the content of glass fiber can reach 20%~60%, and the retained length of glass fiber in the particles can reach 1mm~3mm, compared with PP-SGF materials whose retained length of glass fiber is only 0.2mm~0.4mm, PP-LGF can guarantee the following characteristics due to the three-dimensional network structure of its internal fiber.  1. Low density: The use of long glass fiber reinforced composite material instead of steel is an effective way to reduce the weight of the product.  2. High strength: The composite material with modified resin and different length of fiber has high mechanical strength, good rigidity and impact performance, which can replace steel plate to make coverings or structural parts. 3. Low cost: The use of long glass fiber reinforced composite materials instead of metal materials can simplify the design of complex metal parts and achieve the purpose of forming complex parts at one time. 4. Impact resistance: The elastic deformation property of resin makes long glass fiber reinforced composite materials have certain function of absorbing collision energy, and have a large buffering effect on the impact of certain speed. 5. Corrosion resistance: The composite material has strong corrosion resistance, and its corrosion resistance to acid, alkali and salt is better than that of metal. 6. Beauty: most resins have good colorability, and can be made into various colors by adding masterbatch or spraying paint on the surface; through injection and molding, various irregular curvature shapes can be realized. Datasheet for reference Tests Application As the hottest material, our customers have applied the PP-LGF in many fields, like car parts, washing machine parts, etc. Just contact us, and we will provide technical support. About company Xiamen LFT composite plastic Co., Ltd. is a brand-name company that focuses on LFT&LFRT. Long Glass Fiber Series (LGF) & Long Carbon Fiber Series (LCF). The company's thermoplastic LFT can be used for LFT-G injection molding and extrusion, and can also be used for LFT-D molding. It can be produced according to customer requirements: 5~25mm length. The company's long-fiber continuous infiltration reinforced thermoplastics have passed ISO9001&16949 system certification, and the products have obtained lots of national trademarks and patents.