PP material Polypropylene, PP for short, is a polymer of propylene by adding polymerization. White waxy material, transparent and light in appearance. Polypropylene is a thermoplastic synthetic resin with excellent properties. It is a colorless translucent thermoplastic lightweight general plastic with chemical resistance, heat resistance, electrical insulation, high strength mechanical properties and good high wear-resisting machining properties. PP-LGF material PP plus glass fiber is by adding glass fiber reinforced PP material, due to the addition of glass fiber, limited the mutual movement between polymer chains of PP plastic, therefore, the shrinkage rate of glass fiber reinforced PP (PP plus glass fiber) decreases, rigidity, impact resistance, tensile strength, compression strength, bending strength and flame retardant are improved. The mechanical properties of PP plus glass fiber specifically, tensile strength reached 65MPa--90MPa, bending strength reached 70MPa--20MPa, bending modulus reached 3000MPa--4500MPa, such mechanical strength can be completely comparable with ABS and enhanced ABS products, and more heat resistant. Generally, the heat resistance temperature of ABS and reinforced ABS is between 80℃--98℃, and the heat resistance temperature of glass fiber reinforced PP material can reach 135℃--145℃, and even 150 degrees can withstand more than 1000 hours. Compared with SGF(Short Glass Fiber) TDS for reference only Application of PP-Long glass fiber PP filling long glass fiber material, can be used to make refrigerators, air conditioning and other refrigeration machines in the axial flow fan and fan. In addition, it can also be used to manufacture the inner drum of high speed washing machine, wave wheel, belt wheel to adapt to its high mechanical performance requirements, used for rice cooker base and handle, electronic microwave oven and other places with high temperature resistance requirements, generally speaking, most glass fiber reinforced PP material is used in the structural parts of the product, is a kind of structural engineering materials. Cases Washing machine parts Automobile front end parts Scooter parts Frequently asked questions 1. Does long glass fiber injection have special requirements for injection molding machines and molds? A. There are certainly requirements. Especially from the product design structure, as well as the injection molding machine screw nozzle and mold structure injection molding process must consider the requirements of long fiber. 2. After long glass fiber reinforced, glass fiber can enter the surface of the plastic product during injection molding process, so that the surface of the product become rough and floating fiber. How to make the surface of the material smoothly? A. During injection molding process need to ensure that the plastic particles are well plasticized and dispersed, also ensure that the drying of plastic particles have no moisture removal, mold temperature adjustment to the appropriate temperature, mold surface is polished in place. 3. Can products with appearance requirements be made of long-fiber materials? A. The main feature of LFT-G thermoplastic long glass fiber and long carbon is to show the mechanical properties. If the customer has bright or other requirements for the appearance of the product, it needs to be evaluated in combination with specific products,  

PPA (Polyphthalamide) is polyphthalamide.PPA is a kind of thermoplastic functional nylon with both semi-crystalline structure and non-crystalline structure. It is prepared by polycondensation of phthalic acid and phthalenediamine. It has excellent thermal, electrical, physical and chemical resistance and other comprehensive properties.

Polypropylene, also known as PP or polypropene, is a polyolefin or saturated polymer. It is a low-density thermoplastic with good resistance to heat. Other characteristics of PP include: chemical resistance, elasticity, toughness, fatigue resistance, and electrical insulation capability.

Polyamide, which is also known by the trade name, Nylon, has excellent heat resistant properties, especially when combined with additives and filler materials. In addition to this, Nylon is very resistant to abrasion. Xiamen LFT offers a wide range of temperature-resistant nylons with many different filler materials.

High-density polyethylene (HDPE), also called polyethylene high-density (PEHD), is a thermoplastic polymer made from the monomer ethylene. When used for HDPE pipes, it is sometimes called "alkathene" or "polythene." With a high strength-to-density ratio, High-density polyethylene (HDPE) is used to produce corrosion-resistant piping. In addition, HDPE is commonly recycled.

PPS long carbon fiber reinforced materials combine excellent mechanical strength, high thermal stability, and outstanding chemical resistance. They are ideal for precision parts used in high-temperature, corrosive, or high-stress environments.

Our high-performance PPA (polyphthalamide) long glass fiber reinforced composite is engineered to deliver exceptional mechanical strength, thermal stability, and durability. Designed for demanding applications, this composite material offers a superior balance of stiffness, impact resistance, and processability. Ideal for automotive, electrical, and industrial applications, it sets a new benchmark in high-performance thermoplastic composites.

What is Long Glass Fiber (LGF)? Long glass fiber reinforced plastics (LFT) are engineered materials in which long glass fibers and additives are incorporated into a base thermoplastic. This significantly improves mechanical strength, heat resistance, dimensional stability, and the overall performance of the material. Why Reinforce with Long Glass Fiber? High heat resistance: LFT significantly increases the thermal performance, especially for nylon-based plastics. Reduced shrinkage & higher rigidity: Fiber reinforcement restricts polymer chain movement, improving dimensional stability and stiffness. Improved impact resistance: Reinforced plastics are less prone to stress cracking and have better toughness. High strength: Long glass fibers increase tensile, compressive, and bending strength. Flame retardancy: Most LFT materials are self-extinguishing due to additives and fiber content. Why Choose Long Glass Fiber over Short Glass Fiber? Longer fiber length significantly enhances mechanical properties. High specific stiffness and strength with excellent impact resistance, ideal for automotive applications. Superior creep resistance and dimensional stability for precision parts. Excellent fatigue resistance for long-life components. Improved stability under hot and humid environments. Minimal fiber damage during molding due to relative fiber movement in the mold. Appearance of PP-LGF Applications of PP-LGF Automotive Parts Front end modules, door modules, shift mechanisms, electronic accelerator pedals, dashboards, cooling fans, battery carriers, bumper brackets, underbody protection plates, sunroof frames, etc. – replacing reinforced PA or metal components. Household Appliances Washing machine drums, brackets, air conditioning fans, etc. – replacing short glass fiber reinforced PA and metal components. Communications, Electronics, Electrical Appliances High-precision connectors, igniter components, coil shafts, relay bases, microwave transformer frames, solenoid valve housings, scanner components, etc. Other Applications Power tool housings, water pump/meter housings, impellers, bicycle frames, skis, locomotive pedals, safety helmets, safety shoes – replacing short fiber reinforced PA or PPO. Datasheet for Reference About Us Xiamen LFT Composite Plastics Co., Ltd. is a leading supplier of Long Glass Fiber (LGF) and Long Carbon Fiber (LCF) reinforced thermoplastics. Our LFT materials support injection molding, extrusion molding, and are available in fiber lengths of 5–25mm, tailored to customer requirements. ISO9001 & IATF16949 certified, our products are patented and widely used in automotive, electronics, industrial, and defense applications. What We Offer Technical data and guidance for LFT & LFRT materials. Mold design recommendations for optimized production. Injection molding and extrusion support for consistent product quality.

PA6 Material Overview PA6 (Polyamide 6) is a widely used engineering plastic with excellent balanced performance. Its raw materials are readily available and cost-effective, making it accessible without dependence on foreign technology. However, PA6 has some limitations such as high water absorption, lower low-temperature impact toughness, and moderate dimensional stability. To overcome these limitations, PA6 is often reinforced with glass fiber (GF) to enhance mechanical properties. PA6-LGF (Long Glass Fiber Reinforced PA6) 1. Influence of Glass Fiber Content Glass fiber content is a key factor in the performance of reinforced composites. Increasing fiber content increases fiber density, thinning the PA6 matrix between fibers. This enhances impact toughness, tensile strength, and bending strength. Example: For PA6-LGF, increasing fiber content to 35% raised notch impact strength from 24.8 J/m to 128.5 J/m. However, excessive fiber content can reduce impact strength. Bending strength also improves as fibers transfer stress and absorb energy when broken, with experimental results showing bending modulus up to 4.99 GPa for 35% LGF. 2. Influence of Fiber Retention Length Fiber length significantly affects mechanical properties. When fiber length is below the critical length, increasing length improves resin-fiber bonding and tensile load resistance. When fiber exceeds the critical length, longer fibers absorb more impact energy and improve impact strength, as the number of fiber ends (crack initiation points) decreases. Example: At 40% fiber content, increasing fiber length from 4mm to 13mm improved tensile strength from 154.8 MPa to 164.4 MPa, with bending strength and notched impact strength increasing by 24% and 28%, respectively. Fibers longer than 7mm enhance warping resistance and mechanical stability under high temperature and humidity. Technical Data Reference (TDS) PA6-LGF can be reinforced with 20%-60% long glass fiber depending on product requirements. Compared to unreinforced PA6, PA6-LGF offers enhanced strength, heat resistance, impact resistance, dimensional stability, and reduced warping. The following TDS shows the data for PA6-LGF30. Applications of PA6-LGF PA6-LGF is widely used in automotive, electronic/electrical, and machinery/engineering parts. Automotive Parts Lightweight and miniaturization trends promote PA6-LGF use in engines, electrical systems, and body components. Electronic & Electrical Components Excellent flame retardancy and corrosion resistance make PA6-LGF suitable for switchgear, circuit breakers, contactors, connectors, and cable protection tubes. Mechanical & Engineering Parts Good impact resistance, wear resistance, and self-lubrication properties allow PA6-LGF to be used in machinery and engineering accessories. About Xiamen LFT Composite Plastics Co., Ltd. Xiamen LFT focuses on Long Glass Fiber (LGF) and Long Carbon Fiber (LCF) reinforced thermoplastics. Our LFT materials support injection molding (LFT-G) and extrusion molding, as well as LFT-D molding, with fiber lengths from 5–25mm. Our products are ISO9001 & IATF16949 certified, patented, and widely used in automotive, electronics, industrial, and engineering applications.

PP Material & LFT Solutions body { font-family: Arial, sans-serif; line-height: 1.6; color: #333; margin: 20px; } h2 { font-size: 24px; background-color: #CCCCCC; padding: 10px; } h3 { font-size: 20px; margin-top: 20px; } p { margin: 10px 0; } .highlight { background-color: #FFFF99; color: #333; padding: 5px; } img { max-width: 100%; height: auto; display: block; margin: 10px 0; } ul { margin: 10px 0 10px 20px; } PP Material PP is a polymer made of propylene as monomer by coordination polymerization, and is one of the five major general-purpose plastics: PE, PP, PVC, PS, and ABS. Key Properties: Colorless, tasteless, non-toxic; can meet FDA and other food-grade material requirements when unadded. Due to crystalline nature, the original color is milky white translucent with better transparency than PE. Low specific gravity of 0.9, making it one of the lightest plastics compared to water. Good toughness, especially repeated bending resistance, commonly known as “100-fold rubber”. Better heat resistance than PE, up to 120°C. Good resistance to hydrolysis; can be sterilized by high-temperature steam. Excellent chemical resistance, particularly to acids; suitable for storing concentrated sulfuric acid. Outdoor use is susceptible to light, UV, and aging. Modified PP Material By filling PP with carbon fiber, the rigidity and modulus are increased, reducing deformation caused by shrinkage. However, toughness decreases. Adding anti-UV or anti-aging agents improves outdoor performance, and adding flame retardant materials improves fire resistance. TDS for Reference Only SGF vs LGF Long Carbon Fiber Specification Application Product Processing We Will Offer You LFT & LFRT material technical parameters and leading-edge design Mold front design and recommendations Technical support for injection molding and extrusion molding

PA6 Long Carbon Fiber Composite body { font-family: Arial, sans-serif; line-height: 1.6; color: #333; margin: 20px; } h2 { font-size: 24px; background-color: #f0f0f0; padding: 10px; color: #339933; } p { margin: 10px 0; } ul { margin: 10px 0 10px 20px; } img { max-width: 100%; height: auto; display: block; margin: 10px 0; } Polyamide 6 (PA6) Nylon 6 (PA6) is a general engineering plastic with lightweight, wear resistance, corrosion resistance, and good toughness. As a thermoplastic resin, it softens when heated and hardens when cooled, allowing repeated processing. Long Carbon Fiber Carbon fiber has high strength, high modulus, large specific surface area, and high electrical conductivity. Compared with glass fiber, carbon fiber provides maximum strength along the fiber direction. Carbon fiber reinforced composites are stronger than polymer matrix materials while maintaining light weight, gradually replacing traditional metals in electronics, electric vehicles, medical devices, industrial equipment, and sports/leisure products. LCF VS SCF Advantages of Long Carbon Fiber Filled High strength and high toughness Small coefficient of thermal expansion Low hardness and light weight Corrosion resistance and aging resistance Temperature resistance TDS of PA6 for Reference Application of PA6 Suitable for manufacturing helmets, car bumpers, treadmills, etc. Certifications Factory & Warehouse Teams & Customers About Us Xiamen LFT Composite Plastic Co., Ltd is a brand-name company focusing on LFT & LFRT: Long Glass Fiber Series (LGF) & Long Carbon Fiber Series (LCF). Our thermoplastic LFT materials can be used for LFT-G injection molding, extrusion, and LFT-D molding. Fiber lengths can be customized from 5~25mm. Our continuous infiltration reinforced thermoplastics have passed ISO9001 & IATF16949 certification, and products hold multiple national trademarks and patents.

ABS & Long Glass Fiber Compounds body { font-family: Arial, sans-serif; color: #333; line-height: 1.6; } h2 { font-size: 24px; color: #339933; margin-top: 30px; } h3 { font-size: 20px; color: #339933; margin-top: 20px; } p, ul { font-size: 18px; } ul { margin-left: 20px; } table { width: 100%; border-collapse: collapse; margin-top: 15px; margin-bottom: 15px; } table, th, td { border: 1px solid #000; } th, td { text-align: center; padding: 5px; font-size: 18px; } img { max-width: 100%; margin-top: 15px; margin-bottom: 15px; } What is ABS material? ABS (Acrylonitrile Butadiene Styrene) is a thermoplastic polymer structural material with high strength, good toughness, and easy machinability. ABS appears as opaque ivory grains, but products can be colored and have a high gloss finish. Why fill with Long Glass Fiber? Long fiber reinforced thermoplastics (LFT & LFRT) differ from conventional short fiber reinforced thermoplastics. Short fibers are usually 1–2 mm long, while long fiber processes maintain lengths of 5–25 mm. The long fiber is impregnated with a special resin system, cut to desired lengths, and can be used in injection molding, extrusion, and other applications. This enables direct replacement of steel and thermoset products. Advantages of ABS filling Long Glass Fiber Compounds Glass fiber is heat resistant, increasing the heat resistance of reinforced plastics, especially for nylon plastics. Reduces shrinkage and greatly improves rigidity by limiting polymer chain movement. Prevents stress cracking and significantly improves impact resistance. Enhances mechanical strength, including tensile, compressive, and bending strength. Flame retardancy: Most reinforced plastics cannot ignite due to added fibers and additives. Datasheet for Reference Applications of ABS Filling Long Glass Fiber Compounds Mainly used in load-bearing and structural parts. Product Details Number Length Color MOQ Package Sample Delivery Time Port of Loading ABS-NA-LGF30 5–25 mm Original color (customizable) 25 kg 25 kg/bag Available 7–15 days after shipment Xiamen Port Our Company Our Teams & Customers We Offer You LFT & LFRT material technical parameters and leading-edge design. Mold front design and recommendations. Technical support for injection molding and extrusion molding. Contact Way Ms. Wallis Email: sale02@lfrtplastic.com Whatsapp: (+86) 13950095727 WeChat: 13950095727