PA6 Material Overview PA6 (Polyamide 6) is a widely used engineering plastic with excellent balanced performance. Its raw materials are readily available and cost-effective, making it accessible without dependence on foreign technology. However, PA6 has some limitations such as high water absorption, lower low-temperature impact toughness, and moderate dimensional stability. To overcome these limitations, PA6 is often reinforced with glass fiber (GF) to enhance mechanical properties. PA6-LGF (Long Glass Fiber Reinforced PA6) 1. Influence of Glass Fiber Content Glass fiber content is a key factor in the performance of reinforced composites. Increasing fiber content increases fiber density, thinning the PA6 matrix between fibers. This enhances impact toughness, tensile strength, and bending strength. Example: For PA6-LGF, increasing fiber content to 35% raised notch impact strength from 24.8 J/m to 128.5 J/m. However, excessive fiber content can reduce impact strength. Bending strength also improves as fibers transfer stress and absorb energy when broken, with experimental results showing bending modulus up to 4.99 GPa for 35% LGF. 2. Influence of Fiber Retention Length Fiber length significantly affects mechanical properties. When fiber length is below the critical length, increasing length improves resin-fiber bonding and tensile load resistance. When fiber exceeds the critical length, longer fibers absorb more impact energy and improve impact strength, as the number of fiber ends (crack initiation points) decreases. Example: At 40% fiber content, increasing fiber length from 4mm to 13mm improved tensile strength from 154.8 MPa to 164.4 MPa, with bending strength and notched impact strength increasing by 24% and 28%, respectively. Fibers longer than 7mm enhance warping resistance and mechanical stability under high temperature and humidity. Technical Data Reference (TDS) PA6-LGF can be reinforced with 20%-60% long glass fiber depending on product requirements. Compared to unreinforced PA6, PA6-LGF offers enhanced strength, heat resistance, impact resistance, dimensional stability, and reduced warping. The following TDS shows the data for PA6-LGF30. Applications of PA6-LGF PA6-LGF is widely used in automotive, electronic/electrical, and machinery/engineering parts. Automotive Parts Lightweight and miniaturization trends promote PA6-LGF use in engines, electrical systems, and body components. Electronic & Electrical Components Excellent flame retardancy and corrosion resistance make PA6-LGF suitable for switchgear, circuit breakers, contactors, connectors, and cable protection tubes. Mechanical & Engineering Parts Good impact resistance, wear resistance, and self-lubrication properties allow PA6-LGF to be used in machinery and engineering accessories. About Xiamen LFT Composite Plastics Co., Ltd. Xiamen LFT focuses on Long Glass Fiber (LGF) and Long Carbon Fiber (LCF) reinforced thermoplastics. Our LFT materials support injection molding (LFT-G) and extrusion molding, as well as LFT-D molding, with fiber lengths from 5–25mm. Our products are ISO9001 & IATF16949 certified, patented, and widely used in automotive, electronics, industrial, and engineering applications.

Product number: PA12-NA-LGF Fiber specification: 20%-60% Product feature: High strength, High toughness and durability Product application: Suitable for automotive, sports parts, solar energy, photovoltaic industry and other industries.

PPS & PPS-LGF | High Performance Engineering Plastic body { font-family: Arial, Helvetica, sans-serif; line-height: 1.6; color: #333; } h2 { font-size: 24px; margin-top: 40px; } h3 { font-size: 20px; margin-top: 25px; } p { font-size: 16px; margin: 12px 0; } ul { font-size: 16px; margin-left: 20px; } table { width: 100%; border-collapse: collapse; margin-top: 20px; } table, th, td { border: 1px solid #000; } th, td { padding: 10px; text-align: center; font-size: 16px; } img { max-width: 100%; margin: 20px 0; } What Is PPS? Polyphenylene Sulfide (PPS) is a high-performance engineering thermoplastic known for its excellent heat resistance, chemical stability, flame retardancy, and mechanical strength. Through reinforcement and modification, PPS offers a well-balanced combination of physical, mechanical, and electrical properties. PPS features outstanding dimensional stability, corrosion resistance, and electrical insulation performance, making it suitable for harsh industrial environments. Key Characteristics of PPS Excellent high-temperature resistance High hardness and wear resistance Strong creep resistance under long-term load Excellent electrical properties over a wide temperature range Low sensitivity of mechanical properties to temperature changes Unmodified PPS is naturally brittle and has relatively low impact strength. These limitations can be effectively overcome through fiber reinforcement and material modification. What Is PPS-LGF? PPS-LGF refers to Polyphenylene Sulfide reinforced with Long Glass Fiber. Among engineering plastics, PPS-LGF stands out for its superior heat resistance, structural strength, and long-term reliability. Heat deflection temperature (HDT) above 260°C Chemical resistance second only to PTFE Low molding shrinkage and extremely low water absorption Excellent flame retardancy and vibration fatigue resistance Outstanding electrical insulation even in high humidity and high-temperature environments By incorporating long glass fibers, PPS-LGF significantly improves toughness and impact strength, overcoming the brittleness of pure PPS and delivering excellent comprehensive performance. In many applications, PPS-LGF can replace metals such as stainless steel, copper, aluminum, and alloys—making it an ideal material for metal replacement and lightweight design. Applications of PPS-LGF PPS-LGF is widely used in industries requiring high strength, heat resistance, and chemical stability, including: Automotive components Aerospace structures Household appliances Mechanical and structural parts Chemical processing equipment Electrical insulation and corrosion-resistant components Product Details Grade Color Pellet Length MOQ Packaging Sample Delivery Time Port of Loading PPS-NA-LGF30 Natural (Customizable) ≥ 5–25 mm 25 kg 25 kg / bag Available 7–15 days after shipment Xiamen Port Production Process Our PPS-LGF materials are produced using advanced long-fiber impregnation technology, ensuring excellent fiber length retention, uniform dispersion, and stable mechanical performance. Trademarks and Patents Our materials are supported by proprietary technologies, registered trademarks, and patented processes to ensure consistent quality and reliable performance. Teams and Customers Backed by an experienced R&D and production team, our PPS-LGF materials are trusted by customers worldwide across automotive, industrial, and electrical sectors. What We Offer LFT & LFRT material technical data and advanced design support Mold-front design recommendations and optimization Professional technical support for injection molding and extrusion processing

It takes less energy to produce PLA than petroleum-based thermoplastics, making it relatively eco-friendly. PLA is often regarded as being biodegradable.

PLA Plastic PLA (polylactic acid) is a bio-based polyester and one of the most promising "green plastics" due to its biodegradability, biocompatibility, and high mechanical strength. PLA products can fully degrade into CO₂ and water via microorganisms, and are non-toxic and non-irritating. Mechanically, PLA is comparable to polypropylene, while its gloss, clarity, and processability resemble polystyrene. Its lower processing temperature allows production via injection molding, extrusion, blow molding, spinning, and other common plastic processing methods. PLA is widely applied in disposable plastics, packaging, fibers, nonwovens, chemical, medical, pharmaceutical, and 3D printing industries. PLA is increasingly recognized as a key material to reduce plastic pollution. PLA Reinforced Plastic Glass fiber (fiberglass) is an inorganic material with excellent insulation, heat resistance, corrosion resistance, and high mechanical strength. It is widely used to reinforce composite materials. Long glass fibers are typically over 10mm in length. Long Glass Fiber Reinforced PLA (LGFPLA) contains 10–25mm glass fibers forming a 3D structure during molding. It belongs to long fiber thermoplastics (LFT). Pellet sizes are generally 12mm (injection molding) or 25mm (compression molding). Glass fiber content ranges from 20% to 60%, and colors can be customized. LGF & SGF Advantages Compared with short fiber reinforced thermoplastics, LFT has: Longer fiber length for superior mechanical properties High specific stiffness and strength, excellent impact resistance, ideal for automotive parts Improved creep resistance, dimensional stability, and high precision in molding Excellent fatigue resistance Better stability in high temperature and humid environments Minimal fiber damage during molding due to fiber mobility Technical Details Number Color Length Fiber Content Package Sample Port of Loading Delivery Time PLA-NA-LGF Natural or customized 6-25mm 20%-60% 25kg/bag Available Xiamen Port 7-15 days after shipment Lab & Factory Xiamen LFT Composite Plastic Co., Ltd. Xiamen LFT Composite Plastic Co., Ltd., founded by a thermoplastic composite industry veteran, specializes in the development and production of long glass/carbon fiber reinforced thermoplastic plastics (LFT-G, LFRT, LFT). Our products are lightweight, high-strength, impact- and heat-resistant, recyclable, and eco-friendly. Compared to traditional materials, they offer better corrosion resistance, lower cost, and superior molding performance. Our LFT series (LGF & LCF) include PP, PA6, PA66, PPA, PA12, TPU, PBT, PLA, PET, PPS, and PEEK. Applications cover home appliances, aerospace, automotive, military, and medical equipment, as well as sports goods and daily necessities. Products include gears, rollers, pulleys, pump impellers, fan blades, and more.

Product number: PA12-NA-LGF Fiber specification: 20%-60% Product feature: High strength, High toughness and durability Product application: Suitable for automotive, sports parts, solar energy, photovoltaic industry and other industries.

PP Material & LFT Solutions body { font-family: Arial, sans-serif; line-height: 1.6; color: #333; margin: 20px; } h2 { font-size: 24px; background-color: #CCCCCC; padding: 10px; } h3 { font-size: 20px; margin-top: 20px; } p { margin: 10px 0; } .highlight { background-color: #FFFF99; color: #333; padding: 5px; } img { max-width: 100%; height: auto; display: block; margin: 10px 0; } ul { margin: 10px 0 10px 20px; } PP Material PP is a polymer made of propylene as monomer by coordination polymerization, and is one of the five major general-purpose plastics: PE, PP, PVC, PS, and ABS. Key Properties: Colorless, tasteless, non-toxic; can meet FDA and other food-grade material requirements when unadded. Due to crystalline nature, the original color is milky white translucent with better transparency than PE. Low specific gravity of 0.9, making it one of the lightest plastics compared to water. Good toughness, especially repeated bending resistance, commonly known as “100-fold rubber”. Better heat resistance than PE, up to 120°C. Good resistance to hydrolysis; can be sterilized by high-temperature steam. Excellent chemical resistance, particularly to acids; suitable for storing concentrated sulfuric acid. Outdoor use is susceptible to light, UV, and aging. Modified PP Material By filling PP with carbon fiber, the rigidity and modulus are increased, reducing deformation caused by shrinkage. However, toughness decreases. Adding anti-UV or anti-aging agents improves outdoor performance, and adding flame retardant materials improves fire resistance. TDS for Reference Only SGF vs LGF Long Carbon Fiber Specification Application Product Processing We Will Offer You LFT & LFRT material technical parameters and leading-edge design Mold front design and recommendations Technical support for injection molding and extrusion molding

PA6 Long Carbon Fiber Composite body { font-family: Arial, sans-serif; line-height: 1.6; color: #333; margin: 20px; } h2 { font-size: 24px; background-color: #f0f0f0; padding: 10px; color: #339933; } p { margin: 10px 0; } ul { margin: 10px 0 10px 20px; } img { max-width: 100%; height: auto; display: block; margin: 10px 0; } Polyamide 6 (PA6) Nylon 6 (PA6) is a general engineering plastic with lightweight, wear resistance, corrosion resistance, and good toughness. As a thermoplastic resin, it softens when heated and hardens when cooled, allowing repeated processing. Long Carbon Fiber Carbon fiber has high strength, high modulus, large specific surface area, and high electrical conductivity. Compared with glass fiber, carbon fiber provides maximum strength along the fiber direction. Carbon fiber reinforced composites are stronger than polymer matrix materials while maintaining light weight, gradually replacing traditional metals in electronics, electric vehicles, medical devices, industrial equipment, and sports/leisure products. LCF VS SCF Advantages of Long Carbon Fiber Filled High strength and high toughness Small coefficient of thermal expansion Low hardness and light weight Corrosion resistance and aging resistance Temperature resistance TDS of PA6 for Reference Application of PA6 Suitable for manufacturing helmets, car bumpers, treadmills, etc. Certifications Factory & Warehouse Teams & Customers About Us Xiamen LFT Composite Plastic Co., Ltd is a brand-name company focusing on LFT & LFRT: Long Glass Fiber Series (LGF) & Long Carbon Fiber Series (LCF). Our thermoplastic LFT materials can be used for LFT-G injection molding, extrusion, and LFT-D molding. Fiber lengths can be customized from 5~25mm. Our continuous infiltration reinforced thermoplastics have passed ISO9001 & IATF16949 certification, and products hold multiple national trademarks and patents.